Netgear WFS709TP Manuel d'utilisateur Page 54
- Page / 222
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
WFS709TP ProSafe Smart Wireless Switch Software Administration Manual
2-18 Deploying a Basic WFS709TP System
v1.0, June 2007
• If the APs are not in the same broadcast domain as the WFS709TP, you need to enable
multicast on the network for the WFS709TP to respond to the AP queries. ADP multicast
queries are sent to the IP multicast group address 224.0.82.11. You also need to make sure that
all routers are configured to listen for IGMP join requests from the WFS709TP and that they
can route these multicast packets.
Install APs
When deploying APs, note the AP’s MAC address and serial number as well as its physical
location on the placement map. This is useful in assigning location code identifiers to APs (see “To
configure the location code for an AP:” on page 2-18), which greatly enhances location-based
services and wireless network calibration.
You can either connect the AP directly to a port on the WFS709TP, or connect the AP to another
switch or router that has Layer 2 or Layer 3 connectivity to the WFS709TP.
If the Ethernet port is an 802.3af Power over Ethernet (PoE) port, the AP automatically uses it to
power up. If a PoE port is not available, use the AC adapter shipped with the access point to power
the AP.
Once an AP is connected to the network and powered up, it attempts to locate its WFS709TP using
one of the methods described in “Locate the WFS709TP” on page 2-16.
Provision APs
The next step in AP deployment is to configure or provision each AP. You must minimally
configure each AP with a unique location code that is used for location servicing. The location
code is in the numerical format 1.2.3, where 1 specifies the building, 2 specifies the floor, and 3
specifies the location.
You can also configure IntelliFi RF Management (IRM), a mechanism that enables NETGEAR
APs to optimize their functions in any RF environment. (See “Automatic RF Channel and Power
Settings” on page 1-4.)
To configure the location code for an AP:
1. Navigate to the Maintenance > Program AP page (Figure 2-14).
This page displays a list of APs that have registered with the WFS709TP with either their
default location code (-1.-1.-1) or their currently configured location code (if the AP has
already been provisioned).
- WFS709TP ProSafe 1
- Smart Wireless Switch 1
- Software Administration 1
- Lithium Battery Safety Notice 4
- European Union RoHS 5
- China RoHS 5
- Contents 7
- About This Manual 13
- How to Use This Manual 14
- How to Print this Manual 14
- Revision History 15
- Chapter 1 17
- Overview of the WFS709TP 17
- 1-2 Overview of the WFS709TP 18
- Figure 1-1 18
- Overview of the WFS709TP 1-3 19
- Figure 1-2 19
- 1-4 Overview of the WFS709TP 20
- Figure 1-3 20
- WFS709TP ProSafe Switches 21
- 1-6 Overview of the WFS709TP 22
- WFS709TP Software 23
- Basic WLAN Configuration 24
- Overview of the WFS709TP 1-9 25
- Encryption 26
- Overview of the WFS709TP 1-11 27
- 1-12 Overview of the WFS709TP 28
- Figure 1-5 28
- Association 29
- Overview of the WFS709TP 1-15 31
- 1-16 Overview of the WFS709TP 32
- Overview of the WFS709TP 1-17 33
- Figure 1-6 33
- Figure 1-7 33
- 1-18 Overview of the WFS709TP 34
- Overview of the WFS709TP 1-19 35
- 1-20 Overview of the WFS709TP 36
- Chapter 2 37
- Deployment Scenario #2 38
- Deployment Scenario #3 40
- Configuring the WFS709TP 41
- Run the Initial Setup 42
- Figure 2-4 43
- Figure 2-5 45
- Figure 2-6 45
- Figure 2-7 46
- ← arrow 47
- Figure 2-9 48
- Deploying APs 50
- Figure 2-12 52
- Figure 2-13 52
- Install APs 54
- Provision APs 54
- Figure 2-14 55
- Figure 2-15 55
- Additional Configuration 56
- Chapter 3 57
- Figure 3-1 58
- Figure 3-2 59
- Figure 3-3 59
- Configuring Static Routes 61
- Chapter 4 65
- Before You Begin 66
- Using RF Plan 67
- Building List Page 68
- Building Dimension Page 69
- 4-6 RF Plan 70
- Figure 4-3 70
- Figure 4-4 70
- AP Modeling Parameters Page 71
- 4-8 RF Plan 72
- AM Modeling Parameters Page 73
- Planning Floors Page 74
- RF Plan 4-11 75
- Figure 4-7 75
- 4-12 RF Plan 76
- Figure 4-8 76
- RF Plan 4-13 77
- Figure 4-9 77
- RF Plan 4-15 79
- Figure 4-13 79
- Figure 4-14 79
- 4-16 RF Plan 80
- AP Planning Page 81
- 4-18 RF Plan 82
- Figure 4-16 82
- AM Planning Page 83
- Exporting and Importing Files 84
- RF Plan 4-21 85
- Figure 4-21 85
- Figure 4-22 85
- RF Plan Example 86
- Create a Building 87
- Model the Access Points 88
- Model the Air Monitors 89
- Add and Edit a Floor 89
- Defining Areas 90
- RF Plan 4-27 91
- 4-28 RF Plan 92
- Figure 4-27 92
- Running the AP Plan 93
- Running the AM Plan 94
- 2. Click Save 95
- 4-32 RF Plan 96
- Chapter 5 97
- Configuring WLANS 97
- 5-2 Configuring WLANS 98
- Configuring WLANS 5-3 99
- Determine the Default VLAN 100
- Configuring WLANS 5-5 101
- Figure 5-1 101
- 5-6 Configuring WLANS 102
- Example Configuration 103
- 5-8 Configuring WLANS 104
- Configuring Global Parameters 105
- Add or Modify SSIDs 106
- Configuring WLANS 5-11 107
- Figure 5-3 107
- Configure AP Information 108
- Configuring WLANS 5-13 109
- Figure 5-4 109
- Configuring Radio Settings 110
- Configuring WLANS 5-15 111
- Figure 5-5 111
- 5-16 Configuring WLANS 112
- Add the location 4.2.6 114
- IntelliFi RF Management 115
- Configuring IRM 116
- Configuring WLANS 5-21 117
- 5-22 Configuring WLANS 118
- Chapter 6 119
- Configuring AAA Servers 119
- 6-2 Configuring AAA Servers 120
- Figure 6-1 120
- Configuring AAA Servers 6-3 121
- 6-4 Configuring AAA Servers 122
- Configuring AAA Servers 6-5 123
- 6-6 Configuring AAA Servers 124
- Chapter 7 125
- Figure 7-1 126
- Figure 7-2 127
- 802.1x Authentication Page 129
- Figure 7-4 131
- Chapter 8 133
- Configuring Captive Portal 134
- Figure 8-2 136
- Table 8-1 136
- Changing the Protocol to HTTP 137
- Figure 8-3 138
- Figure 8-4 139
- Figure 8-5 140
- Chapter 9 141
- Configuring Users 142
- Figure 9-2 143
- Chapter 10 145
- Adding Local WFS709TPs 145
- Configuring Local WFS709TPs 146
- Configuring Trusted Ports 147
- Configuring APs 147
- Rebooting APs 148
- Chapter 11 149
- Configuring Redundancy 149
- 11-2 Configuring Redundancy 150
- Figure 11-1 150
- Authentication 151
- Password 151
- Master WFS709TP Redundancy 152
- Configuring Redundancy 11-5 153
- Table 11-2. VRRP Associations 153
- 11-6 Configuring Redundancy 154
- Figure 11-2 154
- Configuring Redundancy 11-7 155
- 11-8 Configuring Redundancy 156
- Chapter 12 157
- Enabling AP Learning 158
- Classifying APs 158
- Figure 12-2 159
- Figure 12-3 160
- Misconfigured AP Detection 161
- Chapter 13 163
- Configuring SNMP 164
- SNMP for Access Points 166
- Figure 13-2 167
- Figure 13-3 169
- Figure 13-4 170
- Figure 13-5 170
- SNMP Traps 171
- Configuring Logging 174
- Figure 13-6 175
- Creating Guest Accounts 176
- Figure 13-11 178
- Managing Image Files 179
- Copying Log Files 180
- Copying Other Files 180
- Chapter 14 183
- Battery Boost 184
- WPA Fast Handover 186
- Appendix A 187
- Windows-Based DHCP Servers 188
- Configuring Option 43 189
- Linux DHCP Servers 190
- Appendix B 193
- Figure B-1 194
- Figure B-2 194
- Figure B-3 196
- Figure B-4 197
- Figure B-5 198
- Figure B-6 199
- Appendix C 201
- Internal Captive Portal 201
- Basic HTML Example 203
- Language Customization 206
- Internal Captive Portal C-11 211
- Figure C-1 211
- Customizing the Welcome Page 212
- Customizing the Pop-Up Box 214
- Appendix D 217
- Related Documents 217
- D-2 Related Documents 218
- Index-4 Index 222
Produits connexes et manuels pour Commutateurs de réseau Netgear WFS709TP
(1 pages)
© 2020, manymanuals.fr. Tous droits réservés | 2.292 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels