Netgear 7200 Series Layer 2 Managed Switch Software Manuel d'utilisateur Page 118
- Page / 158
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
User Manual for the NETGEAR 7200 Series Layer 2 Managed Switch Software
7-76 Switching Commands
202-10010-01
transfer upload filename
This command sets the name for the file that is uploaded from the switch. The switch “remembers”
the last file name used.
Append the file path to the file name if the string is less than 31 characters. Otherwise, use the
“transfer upload path” command, and the File Name will be appended to the File Path.
Note: This command is valid only when the Transfer Mode is TFTP. See “transfer upload mode” .
Default Blank
Format transfer upload filename <name>
transfer upload datatype
This command sets the type of file to upload from the switch.
Format transfer upload datatype
<config|errorlog|msglog|traplog>
The datatype is one of the following:
config Configuration file.
errorlog Error log.
msglog Message log.
traplog Trap log (the default).
transfer upload start
This command starts an upload transfer after displaying current settings and upon confirmation.
Format transfer upload start
transfer download mode
This command specifies whether XMODEM or TFTP mode is used when uploading from the
switch.
Default xmodem. This is valid only when the transfer is initiated by the serial EIA 232
port.
Format transfer download mode <xmodem|tftp>
- User Manual for the 1
- NETGEAR 7200 Series Layer 1
- 2 Managed Switch Software 1
- Technical Support 2
- Trademarks 2
- Statement of Conditions 2
- Contents 5
- Chapter 1 15
- About This Guide 15
- Typographical Conventions 16
- Special Message Formats 16
- About This Guide 1-3 17
- How to Print this Manual 18
- Chapter 2 19
- Chapter 3 21
- Command Line Interface Syntax 21
- Parameters 22
- Conventions 23
- Annotations 24
- Chapter 4 25
- Chapter 5 29
- How to Log In to the GSM7224 30
- Interactive Switch Image 31
- System-Wide Popup Menus 32
- Port-Specific Popup Menus 32
- Chapter 6 33
- Quick Startup 33
- System Info and System Setup 34
- Port (when Slot value is 0): 35
- Quick Startup IP Address 36
- Quick Startup 6-5 37
- The types are: 38
- Address 39
- VLAN Configuration Example 40
- Solution 1 41
- Solution 2 41
- 6-10 Quick Startup 42
- Chapter 7 43
- Switching Commands 43
- 7-2 Switching Commands 44
- Switching Commands 7-3 45
- Switching Commands 7-5 47
- 7-6 Switching Commands 48
- Switching Commands 7-7 49
- 7-8 Switching Commands 50
- Switching Commands 7-9 51
- 7-10 Switching Commands 52
- Switching Commands 7-11 53
- 7-12 Switching Commands 54
- Management Commands 55
- 7-14 Switching Commands 56
- Switching Commands 7-15 57
- 7-16 Switching Commands 58
- Switching Commands 7-17 59
- 7-18 Switching Commands 60
- Switching Commands 7-19 61
- 7-20 Switching Commands 62
- Switching Commands 7-21 63
- 7-22 Switching Commands 64
- Device Configuration Commands 65
- 7-24 Switching Commands 66
- Switching Commands 7-25 67
- 7-26 Switching Commands 68
- Switching Commands 7-27 69
- 7-28 Switching Commands 70
- Switching Commands 7-29 71
- 7-30 Switching Commands 72
- Switching Commands 7-31 73
- 7-32 Switching Commands 74
- Switching Commands 7-33 75
- 7-34 Switching Commands 76
- Switching Commands 7-35 77
- 7-36 Switching Commands 78
- Switching Commands 7-37 79
- 7-38 Switching Commands 80
- Switching Commands 7-39 81
- 7-40 Switching Commands 82
- (MFDB) table 83
- 7-42 Switching Commands 84
- Switching Commands 7-43 85
- 7-44 Switching Commands 86
- Spanning Tree Commands 87
- 7-46 Switching Commands 88
- Switching Commands 7-47 89
- 7-48 Switching Commands 90
- Switching Commands 7-49 91
- 7-50 Switching Commands 92
- Switching Commands 7-51 93
- 7-52 Switching Commands 94
- Switching Commands 7-53 95
- 7-54 Switching Commands 96
- Switching Commands 7-55 97
- 7-56 Switching Commands 98
- Switching Commands 7-57 99
- Security Commands 100
- Switching Commands 7-59 101
- 202-10010-01 101
- 7-60 Switching Commands 102
- Switching Commands 7-61 103
- 7-62 Switching Commands 104
- Switching Commands 7-63 105
- 7-64 Switching Commands 106
- Switching Commands 7-65 107
- 7-66 Switching Commands 108
- Switching Commands 7-67 109
- 7-68 Switching Commands 110
- Switching Commands 7-69 111
- 7-70 Switching Commands 112
- Switching Commands 7-71 113
- 7-72 Switching Commands 114
- Switching Commands 7-73 115
- System Utilities 116
- Switching Commands 7-75 117
- Table 3. TFTP Upload Example 117
- 7-76 Switching Commands 118
- Switching Commands 7-77 119
- 7-78 Switching Commands 120
- Switching Commands 7-79 121
- 7-80 Switching Commands 122
- Chapter 8 123
- Differentiated Services 123
- 8-2 Differentiated Services 124
- Appendix A 125
- Cabling Guidelines 125
- Category 5 Cable 126
- Twisted Pair Cables 127
- Patch Panels and Cables 128
- Cabling Guidelines A-5 129
- Near End Cross Talk (NEXT) 130
- Patch Cables 130
- Cabling Guidelines A-7 131
- Conclusion 132
- Appendix B 133
- Glossary 133
- IP Multicasting 141
- Internet Protocol 141
- Learning 141
- Load balancing 141
- Wide Area Network 150
- ZTerm 4-2 158
Produits connexes et manuels pour Matériel Netgear 7200 Series Layer 2 Managed Switch Software
(6 pages)
Matériel Netgear MA111 Manuel d'utilisateur
(83 pages)
(83 pages)
Matériel Netgear XE102 Manuel d'utilisateur
(22 pages)
(22 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.063 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels